No supplier
Reference: CAR155AUTO0400S
4mm² orange shielded cable *pay per meter!
Reference: CAR155AUTO1000S
10mm² orange shielded cable *pay per meter!
Reference: Gigavac P115 Mini-Tactor
Brand: GIGAVAC
Gigavac P115 Mini-Tactor Contactor P115xDA series relay has a small, lightweight, and cost effective patented design.
Reference: CAR155AUTO5000S
50mm² shielded orange cable, pay per meter!
Banner
Voltage range: 8-20VDC
Power consumption: 5mA when active, 0mA when tripped
Current rating: 50A continuous, 100A intermittent
On-resistance: 1mohm
Dimensions: 71x42x18mm
Weight: 35g
Security policy
Delivery policy (TNT)
Return policy (14 days)
Many EV builders opt to use a smaller auxiliary battery, often Lithium chemistry, for their 12V systems to save space and weight. Unfortunately this means they tend to go flat more quickly if the vehicle is left unattended, which can damage cells.
This device will automatically isolate your 12V battery when its voltage gets low to protect it from further discharge - but with enough charge left to allow the vehicle to get going again when you return. It has low power consumption when monitoring, and by switching its own power off upon low voltage detection, zero current draw once tripped to avoid further discharging your battery.
An onboard LED indicates whether the 12V battery is enabled (on) or disabled (off). The reset input will re-enable the battery for 10 seconds when pressed, giving you enough time to start the vehicle.
The device is simply spliced into the positive wire from your battery, typically using 6mm ring terminals (included). There are also M3 terminals for low power wires to ground and reset (via momentary switch to ground).
Note: Due to the one-way nature of the switch, this device can only block discharge current. Charge current will not be stopped, even if the low voltage threshold has tripped.
No customer reviews for the moment.
Reference: CWHMIO3
Orion 2 Main I/O Wiring Harness – 6 Foot
Reference: OutRep
1 x Plug&Play replacement board of the OEM Outlander slave board, to be used with Orion BMS product line.
Reference: CWH126G
Brand: ORION
Orion 2 BMS Wiring Harness, Cell Voltage Tap Connector for 36 cell, 6ft or 24 ft wire.
Reference: CWH246G
Brand: ORION
Orion 2 BMS Wiring Harness, Cell Voltage Tap Connector for 24 cell, 6ft or 12 ft wire.
Reference: OXMBDISP
Brand: ORION
Orion Basic Display Module + Harness
Reference: TBMSREPPCB-V1
1 x Plug&Play replacement board of the OEM Tesla Model S/X slave board (only for battery modules with silicone balancing wires), to be used with Orion BMS product line.
Reference: typ2socled
Brand: EVSHOP.eu
The module provides visual feedback of the state of charge
Reference: BMWi3rep
1 x Plug&Play replacement board of the OEM BMWi3 slave board (only for battery modules with silicone balancing wires), to be used with Orion BMS product line.
Reference: OXMTHERM80 + CWHTHEXPO2
Brand: ORION
Thermistor Expansion Module
Reference: CWHTHEX202
Thermistor Expansion Module Pre-Wired Harness
Reference: CWH366G
Brand: ORION
Orion 2 BMS Wiring Harness, Cell Voltage Tap Connector for 36 cell, 6ft or 12 ft wire
Reference: CS134XXX
Brand: ORION
ORION 2 Hall Effect Dual Range Current Sensor
Voltage range: 8-20VDC
Power consumption: 5mA when active, 0mA when tripped
Current rating: 50A continuous, 100A intermittent
On-resistance: 1mohm
Dimensions: 71x42x18mm
Weight: 35g
